![]() ![]() Once you’ve secured the scribe in the handle, you’re ready to start marking curves, arcs and other shapes.įinally, if you’re using a pencil-like scribe, you can attach it directly to your workpiece by drilling a hole and screwing in the scribe. Use a drill to drill a hole in the handle and after that you can use a screw to attach the scribe. Use a broom handle for heavy-duty work, or a thinner handle for lighter tasks. Keep in mind the material you’re using, as the handle heavily depends on the type of wood you’re using. If you’re using a woodworking scribe, you can attach it to a handle. Lock in the scribe using the clamp or vice and then you’re ready to start etching and engraving. Put the metal piece in the clamp or vice and position the scribe in such a way that it’s in contact with the metal. Make sure to choose the right size based on the diameter of the scribe and the materials you’re working with. If the scribe is a metal shaping tool, you may need to use a clamp or a vise to secure it in place. Use the same technique as with a face frame cabinet to mark the scribe and trim it to the contour of the wall.Attaching a scribe can be done in a few ways, depending on the type of scribe and materials being used. If you’re using European-style hinges, you can hide the screws behind the hinge mounting plates on the gable. Mount the scribe to the cabinet with two or three screws. You could also mount the scribe flush to the cabinet face, set back from the doors. Note: if you mount the scribe flush to the door face, the front 1/8” or so of the plywood will be visible when the door is open, so it should be the same species as the cabinet exteriors and finished to match. Attach the stile to the edge of the plywood with a few evenly-spaced pocket screws. Rip a stile to the width you need, and cut a rabbet in the back as described earlier. The drawing (top view) shows how to add a scribe to a frameless cabinet.Ĭut a 3 or 4″wide strip of 1/2″ plywood the same height as the cabinet box (excluding the kick space). Make sure the scribes are wide enough to allow drawers to open without hitting door and window casings or other obstructions on adjacent walls. It’s a good idea to plan for scribes early in the design process to get the overall length of the cabinet run right. ![]() The width of the scribe can vary depending on the installation. Frameless Cabinetsįrameless cabinets have a flat end so you need to build a scribe to fit the between the cabinet and the wall. Once you have a good fit you can fasten it in place. Test the fit occasionally to gauge your progress. It’s better to angle the edge slightly towards the back, since the back won’t be visible. Since you’re only sanding a 3/8″ thick edge, it will go quickly. If you use a belt sander be careful not to over sand or round off the edge. Sand the edge of the stile carefully down to the the pencil line. The line should feather to nothing where the gap was the widest. Hold the compass level and against the wall while you mark a pencil line to the bottom of the stile. Pull the cabinet about a 1/2″ from the wall and set the compass to match the widest part of the gap. One way to mark it is to use a pencil compass (remember the old geometry set from school?). Set the cabinet on the kick (or other support if it’s an upper cabinet) at the final height and slide it gently against the wall. Flip the stile so the face is against the fence and run it againĪssemble the frame, attach it to the cabinet and finish it as you normally would.Run the stock face up with the outside (wall) edge against the fence.Set up the table saw with the outside edge of the blade 3/8″ from the fence.Since face frame cabinets already have a stile that projects past the case, it’s easy to add a rabbet to the stile. The approach is slightly different for face frame and frameless cabinets. This means less material to remove with the sander. The key is to cut a 3/8″ x 3/8″ rabbet in the back side of the stile that will meet the wall. With a bit of planning when you’re building the cabinets, you can scribe the cabinet to the wall with just a bit of sanding. ![]() To get a good fit between a cabinet and the wall, without gaps, you need to scribe it to the contour of the wall. In a perfect world, walls would flat and plumb. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |